B69 Dry sodium cyanide or potassium cyanide may be shipped in the following sift-proof and weather-resistant packagings: metal covered hopper cars, covered motor vehicles, portable tanks, or non-specification bins. If it is evident that a package of radioactive material, or conveyance carrying unpackaged radioactive material, is leaking, or if it is suspected that the package, or conveyance carrying unpackaged material, may have leaked, the requirements of 173.443(e) of this subchapter apply. Used or spent dry batteries of both non-rechargeable and rechargeable designs, with a marked rating up to 9-volt that are combined in the same package and transported by highway or rail for recycling, reconditioning, or disposal are not subject to this special provision or any other requirement of the HMR. c. The equipment, and machinery or apparatus articles conforms with 173.222 of this subchapter. (2) A code containing the letter A refers to a special provision which applies only to transportation by aircraft. 352 Ammonium chlorite, ammonium chlorite aqueous solutions, and mixtures of a chlorite with an ammonium salt are forbidden for transport. TP18 The temperature of this material must be maintained between 18 C (64.4 F) and 40 C (104 F) while in transportation. This particularly applies to corrosivity, permeability, softening, premature aging and embrittlement. Others such as copper and silver are available in trace amounts. Sealed packets and articles containing less than 10 mL of a Class 3 liquid in Packing Group II or III absorbed onto a solid material are not subject to this subchapter provided there is no free liquid in the packet or article. 53 Packages of these materials must bear the subsidiary risk label, EXPLOSIVE, and the subsidiary hazard class/division must be entered in parentheses immediately following the primary hazard class in the shipping description, unless otherwise provided in this subchapter or through an approval issued by the Associate Administrator, or the competent authority of the country of origin. 346 Nitrogen, refrigerated liquid (cryogenic liquid), UN1977 transported in accordance with the requirements for open cryogenic receptacles in 173.320 and this special provision are not subject to any other requirements of this subchapter. Filling limits must be in accordance with portable tank special provision TP3. 135 Internal combustion engines installed in a vehicle must be described using Vehicle, flammable gas powered or Vehicle, flammable liquid powered, as appropriate. Additionally, each cylinder must be visually inspected in accordance with CGA pamphlet, CGA C-6 (incorporated by reference, see 171.7). Air must be eliminated from the vapor space by nitrogen or other means. A 25 mm (1 inch) woven lining of asbestos or other approved material must be placed between the bolster slabbing and the bottom of the tank. Pressing enter in the search box 3090 or 3091, as appropriate. b. B76 Tank cars constructed before March 16, 2009, must have a test pressure of 20.68 Bar (300 psig) or greater and conform to Class 105S, 112J, 114J or 120S. A61 a. Shipment of packages under this special provision must be made by private or contract motor carrier. TP37 IM portable tanks are only authorized for the shipment of hydrogen peroxide solutions in water containing 72% or less hydrogen peroxide by weight. b. Alternatively, the item itself may be used as a packaging if it meets the general packaging requirements of subparts A and B of part 173 of this subchapter. Those "other methods" for determining authorized packaging are identified at 173.24 (c) (1) (ii). subject to the Hazardous Materials Regulations must comply with all applicable requirements of Subpart F [172.500]. 19 For domestic transportation only, the identification number UN1075 may be used in place of the identification number specified in column (4) of the 172.101 table. A212 UN 2031, Nitric acid, other than red fuming, with more than 20% and less than 65% nitric acid intended for use in sterilization devices only, may be transported on passenger aircraft irrespective of the indication of forbidden in columns (9A) of the 172.101 table provided that: a. A82 The quantity limits in columns (9A) and (9B) do not apply to human or animal body parts, whole organs or whole bodies known to contain or suspected of containing an infectious substance. B84 Packagings must be protected with non-metallic linings impervious to the lading or have a suitable corrosion allowance for sulfuric acid or spent sulfuric acid in concentration up to 65.25 percent. W10 When offered for transportation by vessel, the use of Large Packagings (see 171.8 of this subchapter) is prohibited. The first label code represents the primary hazard of the material. (1) Numeric provisions. 3 This material is poisonous by inhalation (see 171.8 of this subchapter) in Hazard Zone C (see 173.116(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter. Terminal protection methods include but are not limited to the following: (i) Securely attaching covers of sufficient strength to protect the terminals; (ii) Packaging the battery in a rigid plastic packaging; or. This molecular arrangement is exactly the same as that for dithioketo QA [5]. When column 7 of the Hazardous Materials Table (49 CFR 172.101) includes a special provision code for an entry in the table, the requirement of that code - or codes, there may be several of them - is in addition to the general packaging requirements of 173.24 and any other applicable packaging requirements in Part 173. Do not enter until vapors have dissipated. The driver of the transport vehicle and the consignee(s) must be trained not to enter the transport vehicle until the ammonia vapors have dissipated, and the emergency response information on the shipping paper must indicate that the vehicle contains ammonia vapors. b. Outage must be sufficient to prevent tanks from becoming liquid full at 55 C (130 F). 62 Oxygen generators (see 171.8 of this subchapter) are not authorized for transportation under this entry. Pressure relief devices shall be designed to prevent the entry of foreign matter, the leakage of liquid and the development of any dangerous excess pressure. Column 7 of the 172.101 Hazmat Table lists the special provisions that apply to an individual proper shipping name. Additionally, the offeror must notify the carrier if the tank pressure rise exceeds 3 psig over any 24-hour period. Energy storage capacity means the energy held by a capacitor, as calculated using the nominal voltage and capacitance. Displaying title 49, up to date as of 3/02/2023. shipping name in Column (1) of the 172.101 Table, it means that the mate-rial is known to pose a risk to humans. learn more about the process here. The Code of Federal Regulations (CFR) is the official legal print publication containing the codification of the general and permanent rules published in the Federal Register by the departments and agencies of the Federal Government. The pressure relief device must be preceded by a frangible disk in accordance with the requirements in 178.275(g)(3) of this subchapter to prevent crystallization of the product in the pressure relief device. It must not freeze at temperatures above 15 C (5 F). For non-pressurized lighters containing a Class 3 (flammable liquid) material, its design, description, and packaging must be approved by the Associate Administrator prior to being offered for transportation or transported in commerce. (2) They must be packed in strong outer packagings and the completed package must be capable of withstanding a 1.8 meter (5.9 feet) drop without leakage of gas contents from detectors. or existing codification. (c) Additional air transport requirements. g. The test results shall be documented, shall be traceable, and shall be made available to a representative of the Department upon request. 4 This material is poisonous by inhalation (see 171.8 of this subchapter) in Hazard Zone D (see 173.116(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter. Kits that are carried on board transport vehicles for first aid or operating purposes are not subject to the requirements of this subchapter. For the purpose of this special provision, vehicles are self-propelled apparatus designed to carry one or more persons or goods. TP19 The calculated wall thickness must be increased by 3 mm at the time of construction. When chemical stabilization is employed, the person offering the material for transport shall ensure that the level of stabilization is sufficient to prevent the material as packaged from dangerous polymerization at 50 C (122 F). N92 Notwithstanding the provisions of 173.24(g) of this subchapter, packagings shall be designed and constructed to permit the release of gas or vapor to prevent a build-up of pressure that could rupture the packagings in the event of loss of stabilization. However, the hazard label corresponding to the hazard class or division may be substituted for the marking. TP40 The portable tank must not be transported when connected with spray application equipment. The proper shipping name Paint related material may be used for consignments of packages containing Paint and Paint related material in the same package; b. (9) A code containing the letter W refers to a special provision that applies only to transportation by water. Choosing an item from The identification number used must be consistent on package markings, shipping papers and emergency response information. Table 3 authorizes Large Packagings for specific proper shipping names through the use of IB Codes assigned in the 172.101 table of this subchapter. The proper shipping name Paint related material, corrosive, flammable may be used for consignments of packages containing Paint, corrosive, flammable and Paint related material, corrosive, flammable in the same package; c. The proper shipping name Paint related material, flammable, corrosive may be used for consignments of packages containing Paint, flammable, corrosive and Paint related material, flammable, corrosive in the same package; and. Each portable tank constructed of metal must be fitted with a pressure-relief device consisting of a reclosing spring loaded type, a frangible disc or a fusible element. A rocket motor to be considered nonpropulsive must be capable of unrestrained burning and must not appreciably move in any direction when ignited by any means. Large Packagings are authorized for the Packing Group III entries of specific proper shipping names when either special provision IB3 or IB8 is assigned to that entry in the 172.101 Table. W9 When offered for transportation by water, the following Specification packagings are not authorized unless approved by the Associate Administrator: woven plastic bags, plastic film bags, textile bags, paper bags, IBCs and bulk packagings. View the most recent official publication: These links go to the official, published CFR, which is updated annually. 21 This material must be stabilized by appropriate means (e.g., addition of chemical inhibitor, purging to remove oxygen) to prevent dangerous polymerization (see 173.21(f) of this subchapter). 150 This description may only be used for ammonium nitrate-based fertilizers. c. Packagings are excepted from the design stress limits at elevated temperatures, as described in Section VIII of the ASME Code (IBR, see 171.7 of this subchapter). N12 Plastic packagings are not authorized. If you have questions for the Agency that issued the current document please contact the agency directly. N34 Aluminum construction materials are not authorized for any part of a packaging which is normally in contact with the hazardous material. b. Gases of Division 2.3 and gases with a subsidiary risk of 5.1 must not be used as a propellant in a chemical under pressure. 171 This entry may only be used when the material is transported in non-friable tablet form or for granular or powered mixtures that have been shown to meet the PG III criteria in 173.127. When such batteries are transported in accordance with 173.185(c), the total lithium content of all lithium metal cells contained in the battery must not exceed 1.5 g and the total capacity of all lithium ion cells contained in the battery must not exceed 10 Wh. This web site is designed for the current versions of The numbers and letters in the special provisions column are referred to in 49 CFR 172.102 with an explanation of their meanings. N83 This material may not be transported in quantities of more than 11.5 kg (25.4 lbs) per package. 121 This substance, when containing less alcohol, water or phlegmatizer than specified, may not be transported unless approved by the Associate Administrator. (3) Damage to terminals. 128 Regardless of the provisions of 172.101(c)(12), aluminum smelting by-products and aluminum remelting by-products described under this entry, meeting the definition of Class 8, Packing Group II and III may be classed as a Division 4.3 material and transported under this entry. The cargo transport unit shall display the UN number in a manner in accordance with 172.332 of this subchapter and be placarded on two opposing sides. (ii) One bottle for every two hours of production, or for every 2,500 bottles produced, must be tested by dropping a bottle filled to 98 percent capacity with water from a height of 1.2 meters (3.9 feet) onto solid concrete directly on the closure. 328 When lithium metal or lithium ion batteries are contained in the fuel cell system, the item must be described under this entry and the appropriate entries for Lithium metal batteries contained in equipment or Lithium ion batteries contained in equipment. Prohibited means bottom openings are prohibited, and Prohibited for liquids means bottom openings are authorized for solid material only. 1 CFR 1.1 If the material has a flash point of less than 38 C (100 F), then the bulk packaging requirements of 173.242 of this subchapter are applicable. The official, published CFR, is updated annually and available below under W31 Non-bulk packagings must be hermetically sealed. B25 Packagings must be made from monel or nickel or monel-lined or nickel-lined steel. 350 Ammonium bromate, ammonium bromate aqueous solutions, and mixtures of a bromate with an ammonium salt are forbidden for transport. B134 For Large Packagings offered for transport by vessel, flexible or fibre inner packagings shall be sift-proof and water-resistant or shall be fitted with a sift-proof and water-resistant liner. The battery has been tested as a primary lithium battery; and. For transportation by aircraft, cargo transport units may only be offered for transportation and transported under conditions approved by the Associate Administrator. For transportation by aircraft, a telephone report in accordance with 171.15(a) is required if a fire, violent rupture, explosion or dangerous evolution of heat (i.e., an amount of heat sufficient to be dangerous to packaging or personal safety to include charring of packaging, melting of packaging, scorching of packaging, or other evidence) occurs as a direct result of a dry battery. b. Stacking is permitted two or more levels high to achieve maximum allowable utilization of the designated vehicle, rail car weight, or intermodal freight container weight or vessel hold volume. c. Primary receptacles may also be further packed in specification bulk outer packagings. TP31 This hazardous material may only be transported in tanks in the solid state. In this case, some parts of the vehicle may be detached from its frame to fit into the packaging. here. The packing group assignment and packaging must be approved by the Associate Administrator for Hazardous Materials Safety on the basis of the criteria in 173.21 of this subchapter and the package type used for the Series 6(c) test. When column 7 of the 172.101 table refers to a special provision for a hazardous material, the meaning and requirements of that provision are as set forth in this section. authorized by name in the Hazardous Materials Table or have been specifically authorized by name either in the Section 172.101 Hazardous Materials Table or have been assigned a shipping name and hazard class by the Associate Administrator for Hazardous Materials Safety. (7) The design type of the article must be subjected to the following test. 110 Fire extinguishers transported under UN1044 and oxygen cylinders transported for emergency use under UN1072 may include installed actuating cartridges (cartridges, power device of Division 1.4C or 1.4S), without changing the classification of Division 2.2, provided the aggregate quantity of deflagrating (propellant) explosives does not exceed 3.2 grams per cylinder. For Federal Register citations affecting 172.102, see the List of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and at www.govinfo.gov. 130 Batteries, dry, sealed, n.o.s., commonly referred to as dry batteries, are hermetically sealed and generally utilize metals (other than lead) and/or carbon as electrodes. 182 Equipment containing only lithium batteries must be classified as either UN 3091 or UN 3481. 166 When transported in non-friable tablet form, calcium hypochlorite, dry, may be transported as a Packing Group III material. When a placard is displayed, the placard must be the placard shown in 172.560. While columns 8 and 7 of the Hazardous Materials Table are used to determine authorized packaging for most HazMat (more on that in a little bit), some methods of transportation, HazMat quantities, and specific operations rely on other methods. The tank car specification may be marked to indicate a test pressure of 20.68 Bar (300 psig). A54 Irrespective of the quantity limits in Column 9B of the 172.101 table, a lithium battery, including a lithium battery packed with, or contained in, equipment that otherwise meets the applicable requirements of 173.185, may have a mass exceeding 35 kg if approved by the Associate Administrator prior to shipment. Table 1. 11 The hazardous material must be packaged as either a liquid or a solid, as appropriate, depending on its physical form at 55 C (131 F) at atmospheric pressure. full text search results The adsorption or absorption presents the following properties: (1) The pressure at a temperature of 20 C (68 F) in the receptacle is less than 0.6 bar (60 kPa); (2) The pressure at a temperature of 35 C (95 F) in the receptacle is less than 1 bar (100 kPa); (3) The pressure at a temperature of 85 C (185 F) in the receptacle is less than 12 bar (1200 kPa). This entry may not be used for solids containing a Packing Group I liquid. The tank car specification may be marked to indicate a test pressure of 13.79 Bar (200 psig). Each tank car must have a reclosing pressure relief device having a start-to-discharge pressure of 15.51 Bar (225 psig). (8) A code containing the letters TP refers to a portable tank special provision for UN or IM Specification portable tanks that is in addition to those provided by the portable tank instructions or the requirements in part 178 of this subchapter. IBCs are only authorized if approved by the Associate Administrator. 362 This entry applies to liquids, pastes or powders, pressurized with a propellant that meets the definition of a gas in 173.115. 125 Lactose or glucose or similar materials may be used as a phlegmatizer provided that the substance contains not less than 90%, by mass, of phlegmatizer. TP44 Each portable tank must be made of stainless steel, except that steel other than stainless steel may be used in accordance with the provisions of 173.24b(b) of this subchapter. Prior to repacking into the life-saving appliance, an installed inflation cylinder must successfully meet and pass all inspection and test criteria and standards of the raft manufacturer and the vessel Flag State requirements for cylinders installed as part of life-saving appliances, self-inflating (UN2990) used on marine vessels. Essentially, such SSolder complies with RoHS (Restriction of Hazardous Substances) regulations. In addition, there are over 300 numeric codes provisions. A metal hydride storage system installed in or intended to be installed in a vehicle or equipment or in vehicle or equipment components must be approved for transport by the Associate Administrator. See Batteries, dry, sealed, n.o.s. in the 172.101 Hazardous Materials Table (HMT) of this part for transportation requirements for nickel-metal hydride batteries transported by other modes and for nickel-metal hydride button cells or nickel-metal hydride cells or batteries packed with or contained in battery-powered devices transported by vessel. police activity south hill puyallup,
Iowa City Drug Bust, Articles C